Step One
Surface Preparation: Normal Dirt
Muticlean Extra Strength Cleaner
Instructions for Use
1. Normal dirt: Use one spoonful of cleaner per one gallon of water. Heavy dirt: Use at full strength.
2. Apply solution with a mop, sponge or rag. Scrub as necessary.
3. Rinse surface thoroughly with clean water and wet vac residue.
4. Let surface completely dry before polishing.
5. Yields 1000-1300 sq.ft. under normal use
Warnings: Do not swallow-Keep away from reach of children. Avoid contact with eyes
and skin.
Step Two
Long Term Protection: Superseal Impregnator
Instruction for Use
1. Apply the product evenly on the surface to be protected, insuring thorough saturation.
2. Repeat step 1 within 1-2 hours of initial application.
3. If a slight film remains on surface, wipe off with a cloth soaked in the product.
4. Allow surfaces to dry overnight.
5. Yields 105 sq.ft. per liter depending upon the porosity of the stone.
Warnings: Flammable-Avoid contact with eyes.
Step Three
New or Newly Restored Floors:
Evershine Stone polish Wax
Instructions for Use
1. Wash floor with Multi Clean or Multi Strip to removes any traces of dirt and old waxes. Rinse and wet vac. Allow floor to thoroughly dry.
2. Dilute 2 capful of Ever Shine to 1 gallon of water.
3. Spread evenly over entire surface using a clean rag, sponge, mop or a lamb?™s wool applicator. Allow floor to dry to haze before walking on it.
4. Buff using a 175 rpm floor machine with a soft pad.
5. Use clean, cold water or PolyWash for daily floor maintenance. Do Not Use Soap.
6. Repeat 15 days to 4 months, depending upon foot traffic.
7. 1 liter treats 1600-1615 sq.ft.
Step Four
Ongoing maintenance and Protection:
Polywash Stone Soap (For daily use)
Instruction for Use
1. Dilute 1-2 capfuls of product to 1 gallon of water, depending upon amount of dirt and foot traffic. Apply with a clean mop.
2. Allow to thoroughly dry. Polish with a woolen cloth or a 175 rpm polishing machine using a white disc.
3. Yield: 1 liter treats approximately 2000-2100 sq.ft.
Warnings: Do not swallow- Do not inhale. Keep away from children. Avoid contact with eyes.
Step Five
Stripping and Stain Removal: Multi Strip
Multi Strip removes old emulsified wax (natural and synthetic wax), resin-based, normal wax, water-based and self-polishing wax from floors and walls. Multi Strip will not damage polished Marble.
Instruction for Use
1. Dilute 10/20 capfuls in 1 liter of water to remove normal wax and wax with a single disc polishing machine or use a mop.
2. Dilute 50 capfuls in 1 liter of water to remove strong, old or self-polishing wax and wash with Multi Clean.
3. After washing, rinse the floor thoroughly with water and wet vac residue. Allow to completely dry before waxing.
4. Yield: 1 liter treats approximately 500-1000 sq.ft.
Warnning: Do not swallow- do not inhale. Keep away from children- Avoid contact with eyes and skin.
Stubborn stains may require the use of a poultice Mangia Macchia, ??The Stain Eater??is applied directly over the stain. Use a plastic saran wrap to cover the poultice, allowing the affects of humidity to draw the stain out of the stone. Remove the plastic and allow the poultice to dry to a powder. Brush off. Repeat if necessary.
Step Six
Repolishing: Stone King 5X-tra polishing powder
Instructions for Use
1. Wash the floor with Multi Clean and/or Multi Strip to removes all dirt and traces of old wax residue. Rinse well and wet Vac.
2. Spread a handful of Marble Powder 5X over a small area of the floor. Add water and pass over with a floor polishing machine with steel wool pads to make a slurry.
3. Test a small patch to see if the desired shine has been achieved. Rinse or mop well with clean cold water and wet vac. Allow to thoroughly dry.
4. Follow Steps 1-3.
Dr. Sal?™s Magic Stone Crème
Instruction for Use
1. Remove any topical coatings using Multi Strip and a single disc machine fitted with a cleaning disc or brush for washing. Rinse well and wet vac.
2. Wet an approximate 10 square foot area with clean water. Do Not Flood The Area.
3. Apply 2 tablespoons, (1oz) of Polishing Crème in the center of the area. Using a 175 rpm polishing machine with 50 lbs. of weight and fitted with a hog?™s head pad, 000 steel wool pad or a felt pad, start polished by slowly moving the machine in a side by side motion. (A hot disc eliminates need for weights)
4. Spray the surface with water 10 maintain a creamy slurry. Continue polishing in a side by side motion for 10 minutes or more as necessary until the crème has dried up and the desired level of polish has been achieved.
5. Flood rinse and wet vac the area.
6. Repeat this process in the next area, overlapping the previous area to blend.
7. Check the surface periodically to determine the desired level of shine
8. When finished, clean the surface with Ever Shine Cleaner and Polisher. Buff with a clean, white buffing pad to a brilliant gloss.
9. 35 oz. of product treats 300/550 sq.ft.
|
View Map on Website
